Search results

Nice! Sent from my iPad using Tapatalk

Been 6 years since I was at this one. Sent from my iPad using Tapatalk

Beiland, you know there is a show at the Prime Osborne Center in Jax on the 10th, right? Just moved back to Jax from Charlotte last month, and found it. Sent from my iPad using Tapatalk

Okay, looks like I got it to be Quiet.... Here's the reply I got from Soundtraxx, and just now had chance to test...... Mike, Thank you for contacting SoundTraxx Support. On page 37 of the Tsunami2 Steam User's Guide there is a list of Primary Mixer Volume Level CVs. The sounds you're hearing...

Yes they are. Replied very quickly. Sent from my iPad using Tapatalk

Tsunami2, T-1100 Startup "Idle Chuff" Turnoff.... I contacted Soundtraxx, and they lead me to the sheets in the user manual to which one of two to try and turn down the CVs.....gonna try it tonight, and I'll post the results. Mike Sent from my iPad using Tapatalk

As I'm finding out.....it is confusing....maybe time to invest in JMRI...... Sent from my iPad using Tapatalk

Thanks Toot for the Lead.....I actually still need the sound....For the Waterstop and Ash Dump, only when Filling the Loco's....I'll let you what I come up with. Mike Sent from my iPad using Tapatalk

Not a manual per se, just the typical installation card and functions guide. I've downloaded the T2 Steam manual. I'll also try Selectors suggestion for the compound and/or single pumps.... Sent from my iPad using Tapatalk

I am finishing up an FSM Water Tank/Tool Shed, and have Animated the the Water Spout. I've installed a Tsunami 2, T-1100 to Drive the Tamiya 1600:1 Gear Box, and to use the Waterstop Sound from Loading Water into my Geared Locos. However, as with all of my Soundtraxx Decoders, whenever power...

Sorry Guys & Girls, I just realized I posted this in the wrong spot...going to post in the DCC Forum. My Bad. Sent from my iPad using Tapatalk

I am finishing up an FSM Water Tank/Tool Shed, and have Animated the the Water Spout. I've installed a Tsunami 2, T-1100 to Drive the Tamiya 1600:1 Gear Box, and to use the Waterstop Sound from Loading Water into my Geared Locos. However, as with all of my Soundtraxx Decoders, whenever power...

There wasn't/isn't a template per se, as I'm sure each Helix has its own idiosyncrasies , I merely pointed this out, as he went thru the steps for creating his "templates", then the process of laying out on the sheets. Albeit, it was for an N Scale Helix, but I'd imagine the steps would be the...

If you are a MR Video Plus subscriber, David Popp just had a great video on laying out Helix cuts for their Canadian Canyon Layout Series. Very little waste...lots of pieces. Sent from my iPad using Tapatalk

I'm getting a dead "This video is not available" link. Sent from my iPad using Tapatalk

Thanks Willie....I tried to think of every conceivable reason.....except that. Makes sense now. Thanks again. Mike Charlotte, NC area Sent from my iPad using Tapatalk

I'm a steam guy, turn of the century Logging in Particular. So I'm asking a stupid question about Diesel Loco's. 99% of videos or pictures I see of Double Headed Trains, I see the Lead Loco facing frontwards, and the 2nd facing to the rear.....my question is....WHY? I've gone over in my head...

Experience tells me (although I only run Stream Logging Locos), that really doesn't matter 'where' the Decoder resides...... but rather that it's wired correctly and that (assuming) the two will always will be together the connections between to two units are good and secure. Sent from my iPad...

Just as a first check...have you tried running on DC only to see if it runs well.....trying to eliminate Mechanical issues 1st. Sent from my iPad using Tapatalk

As I am approaching 60, I can appreciate that last line!,,, Sent from my iPad using Tapatalk